日本油研平衡閥，YUKEN平衡閥型號

上海乾拓貿易有限公司 

　企業QQ：2880626087

　電話；021-69001039

　手機；17321017802（微信）

　郵箱；17321017802@163.com

　地址：上海市嘉定區江橋嘉涌路99弄6號樓713室A

因此，盡量減少管內的直徑和長度。

 Please maintain the degree of contamination with-in NAS 1638-Grade 12.  Use 25 μm or finer line filter.

Instructions To use remote control relief valve in the venting circuit, see the Catalogue No. Pub. EC-0201. 

 If the internal volume of the vent line is too large, chattering is likely to occur.  

將油箱管道連接到任何其他管路，但直接連接到油箱。

減壓和減壓閥的特點和應用由減壓閥，安全閥（用于平衡）

和止回閥組成的常規電路可以用一個減壓和減壓閥代替。

可以使用下表中列出的任何類型的液壓油。

Thus, as far as possible reduce the inside Dia and t he length of the pipe. 

To adjust the pressure, loosen the lock nut and turn the pressure adjustment handle slowly clockwise for higher pressures 

and anti-clockwise for lower pressures. After adjustments, do not forget to tighten the lock nut.

使用25μm或更細的線路濾波器。

說明在通風回路中使用遙控安全閥，請參見目錄號。

請保持在NAS 1638-Grade 12中的污染程度。

這使得能夠容易地調節平衡壓力，

并且允許電路大大簡化，導致成本較。

如果負載變化，只能通過操作壓力調節手柄來平衡壓力。

減壓和減壓閥可應用于液壓平衡電路，如加工中心的平衡機構。

Any type of hydraulic fluids listed in the table below can be used.

Note:For use with hydraulic fluids other than those listed above，

 EC-0201。如果排氣管線的內部體積過大，則可能發生顫動。

 Pressure is limited by collars fitted.  If a working pressure cannot be attained, remove some collars.  

One collar is equivalent to 10 MPa (1450 PSI). Connect the tank pipe not to any other line but directly to the tank.

要調節壓力，請松開鎖緊螺母，

并慢慢順時針轉動壓力調節手柄，以獲得更高的壓力，

并在較的壓力下逆時針旋轉壓力調節手柄。

調整后，請勿忘記擰緊鎖緊螺母。

Pressure reducing and relieving valves are composite pressure control valves having pressure reducing 

and counterbalancing functions devel-oped f or hydraulic balancing circuits.

減壓和減壓閥是具有減壓和平衡功能開發的液壓平衡回路的復合壓力控制閥。

污染控制必須注意保持對液壓油污染的控制，

Recommended Viscosity and Oil Temperatures 2  Viscosity ranging between 15 - 400 mm /s (77 - 1800 SSU). 

 Oil temperatures between -15/+70°C (5 - 158°F).  Use hydraulic fluids

 which satisfy the recommended viscosity and oil temperatures given above.

Control of Contamination Due caution must be paid to maintaining control over contamination of the hydraulic fluids 

which may otherwise lead to breakdowns and shorten the life of the valves. 

壓力受套圈的限制。

如果無法達到工作壓力，請取出一些項圈。

一個領相當于10 MPa（1450 PSI）。

TJ的粘度和油溫2粘度范圍在15 - 400 mm / s（77 - 1800 SSU）之間。

油溫在-15 / + 70°C（5 - 158°F）之間。

使用滿足上述給出的TJ粘度和油溫的液壓油。

否則可能會導致故障的破壞并縮短閥門的使用壽命。

日本油研平衡閥，YUKEN平衡閥型號